Hola,
¿eres nuevo aquí?

Regístrate gratis y conecta tu empresa con financiación pública, partners y proyectos.

Tengo cuenta

Regístrate

Ver video

GUDGET

Financiado

Cerrado

GUst generators and model DesiGn for transonic wind tunnel tEsTs

GUDGET answers the CfP JTI-CS2-2018-CfP08-AIR-01-38 and aims at providing an innovative experimental set-up for the investigation of gust loads, to be installed in the transonic facility ONERA S3Ch. The proposal GUDGET will design... ver más

28/02/2023

IBK Innovation Gmb...

1M€

Presupuesto del proyecto: 1M€

Líder del proyecto

IBKINNOVATION GMBH CO. KG No se ha especificado una descripción o un objeto social para esta compañía.

TRL 4-5

Fecha límite participación Sin fecha límite de participación.

Ver 6 Participantes

Financiación concedida El organismo H2020 notifico la concesión del proyecto el día 2023-02-28

JTI-CS2-2018-CfP08-AIR-01-38: Innovative test rig for the investi...

I+D

Cerrada hace 6 años

0% 100% 100%

Información adicional privada

No hay información privada compartida para este proyecto. Habla con el coordinador.

6 Participantes

IBK Innovation GmbH&Co. KG

362.25K€ | Lider

GOLDEN FOODS

328.17K€ | Participante

CEDRAT TECHNOLOGIES SA

277.00K€ | Participante

POLIMI

114.00K€ | Participante

Conecta tu I+D

¿Tienes un proyecto y buscas un partner? Gracias a nuestro motor inteligente podemos recomendarte los mejores socios y ponerte en contacto con ellos. Te lo explicamos en este video

Proyectos interesantes

ESTRO Experimental and theoretical aSsessmenT of laminaR flow rObu... 1M€ Cerrado

NEXTTRIP NEXT generation civil Tilt Rotor Interactional aerodynamic t... 3M€ Cerrado

ETRIOLLA Experimental TRansonic Investigations On Laminar flow and Lo... 4M€ Cerrado

GLAMOUR Gust Load Alleviation techniques assessment on wind tUnnel M... 2M€ Cerrado

HiReLF Transonic High Reynolds Number Testing of a Large Laminar Wi... 1M€ Cerrado

ERaCLE invEstigation of pushing pRopeller engine Configurations tro... 1M€ Cerrado

Duración del proyecto: 48 meses Fecha Inicio: 2019-02-13
Fecha Fin: 2023-02-28

Líder del proyecto

IBKINNOVATION GMBH CO. KG No se ha especificado una descripción o un objeto social para esta compañía.

TRL 4-5

Presupuesto del proyecto 1M€

Fecha límite de participación Sin fecha límite de participación.

Descripción del proyecto GUDGET answers the CfP JTI-CS2-2018-CfP08-AIR-01-38 and aims at providing an innovative experimental set-up for the investigation of gust loads, to be installed in the transonic facility ONERA S3Ch. The proposal GUDGET will design, manufacture, calibrate, verify and finally install in the ONERA S3Ch WT an enhanced gust generator system and an aeroelastic half-model connected to the WT side wall, with the purpose to support the TM in the execution of a WT test campaign and gather information on the aeroelastic behaviour of the model under high amplitude gust conditions, with the acquisition of a relevant database which will allow to assess the numerical capabilities to predict gust loads. The WT test campaign is outside the scope of the GUDGET project. At this aim, the consortium GUDGET has to perform the design of the experimental setup: design and manufacture the WT model according to technical requirements provided by the TM. Special care will be dedicated to the dynamic characteristics of the final model and that a specific interface with the WT will be implemented. In parallel, the consortium will perform a preliminary trade-off analysis to find the best configuration of the GG to comply with requirements dictated in the topic, by considering innovative configurations of tilting airfoils moved by mechanical actuators as well as blowing slots fed by fluidic actuators or a combination of both. The best solution over a number of candidates will be chosen as the one to be designed in detail and then manufactured, calibrated/ verified and eventually installed in the WT. The GUDGET consortium has been setup by joining well recognized and very experienced companies and universities: IBK and POLIMI with a strong experience in the design, manufacturing and operating of WT models; DREAM for supporting CFD and numerical analysis; AVDES for the manufacturing activities and CTEC for the design and implementation of actuation devices.

Conecta tu I+D

Entra hoy

¿Olvidé mi contraseña?

Financiación

Empresas

CTIs/Universidades

Proyectos

Investigadores