Hola,
¿eres nuevo aquí?

Regístrate gratis y conecta tu empresa con financiación pública, partners y proyectos.

Tengo cuenta

Regístrate

Ver video

CleanSky-LBD

Financiado

Cerrado

Adaptation of a generic wind tunnel model for attachment line transition measure...

Adaptation of a generic wind tunnel model for attachment line transition measurements The Hybrid Laminar Flow Technology for drag reduction needs small holes for boundary layer suction. This proposal addresses the perforation and integration of inserts for flow tunnel tests. Therefore, an approved laser process at... ver más

31/10/2014

BIAS GmbH

299K€

Presupuesto del proyecto: 299K€

Líder del proyecto

BIAS BREMER INSTITUT FUR ANGEWANDTE STRAHLTE... No se ha especificado una descripción o un objeto social para esta compañía.

TRL 4-5

Fecha límite participación Sin fecha límite de participación.

Financiación concedida El organismo FP7 notifico la concesión del proyecto el día 2014-10-31 No tenemos la información de la convocatoria

0% 75% 100%

Información adicional privada

No hay información privada compartida para este proyecto. Habla con el coordinador.

1 Participantes

BIAS GmbH

0.00€ | Lider

Conecta tu I+D

¿Tienes un proyecto y buscas un partner? Gracias a nuestro motor inteligente podemos recomendarte los mejores socios y ponerte en contacto con ellos. Te lo explicamos en este video

Proyectos interesantes

ALVAR Advance Laminar Flow Control with Variable Porosity 794K€ Cerrado

COMPACT COMbined Passive and Active Flow Control Technology Wing 2M€ Cerrado

DELASTI DEvelopment of advanced LASer based technologies for the man... 449K€ Cerrado

ATHENAI Aerodynamic Testing of Helicopter Novel Air Intakes 447K€ Cerrado

DEAFCON Wind Tunnel Model Design with Active Flow Control for Low... 219K€ Cerrado

GBSSD(3) Ground Based Structural Systems Demonstrator Phase 3 Com... 3M€ Cerrado

Líder del proyecto

BIAS BREMER INSTITUT FUR ANGEWANDTE STRAHLTE... No se ha especificado una descripción o un objeto social para esta compañía.

TRL 4-5

Presupuesto del proyecto 299K€

Fecha límite de participación Sin fecha límite de participación.

Descripción del proyecto The Hybrid Laminar Flow Technology for drag reduction needs small holes for boundary layer suction. This proposal addresses the perforation and integration of inserts for flow tunnel tests. Therefore, an approved laser process at BIAS for drilling suction holes for flow meters shall be transferred to an adequate system technology for large inserts using a short pulsed fibre laser with high power as recently available on the laser market. The process parameters must be adapted to the new system technology. This will be done by investigation of drilled hole geometries and tolerances using transmitted light microscopy with automated edge detection, which will be calibrated using prepared cross-sections of the holes. The efficient machining speed and fast analysis methods also enable to reconfigure an insert if the achieved results of the wind tunnel tests make this necessary. The following steps shall be done to investigate the production of wind tunnel inserts: Installation/configuration of the drilling system, process development for laser drilling, manufacturing of test specimen and hole analysis, upscaling of laser drilling procedure, manufacturing of 3 suction inserts, integration of suction inserts into model. Within this project the system technology and knowledge about the necessary drilling technology for inserts usable in flow tunnel tests is developed. Furthermore, the feasibility is proven in form of a full size model. This is a contribution to the targets of the CleanSky programme as the successful production of an insert for wind tunnel tests can significantly contribute to the technological breakthrough and shorten the time to market of the suction hole technology, thus contributing significantly to reducing the environmental footprint of aviation.

Conecta tu I+D

Entra hoy

¿Olvidé mi contraseña?

Financiación

Empresas

CTIs/Universidades

Proyectos

Investigadores